Einrichten von smartctl unter Suse und Debian:
Meine Festplatte SAMSUNG HD502IJ an /dev/sdb scheint nicht mehr richtig zu funktionieren:
~~~ $ sudo smartctl -s on --tolerance=permissive -a /dev/sdb smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-14-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, [smartmontools.sourceforge.net](http://smartmontools.sourceforge.net) Vendor: /3:0:0:0 Product: User Capacity: 600.332.565.813.390.450 bytes [600 PB] Logical block size: 774843950 bytes >> Terminate command early due to bad response to IEC mode page unable to fetch IEC (SMART) mode page [scsi response fails sanity test] A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. ~~~ Die Festplatte /dev/sdc liefert ein besseres Ergebnis: ~~~ $ sudo smartctl -s on --tolerance=permissive -a /dev/sdc smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-14-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, [smartmontools.sourceforge.net](http://smartmontools.sourceforge.net) === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD5000AAKS-00V1A0 Serial Number: WD-WMAWF0713191 LU WWN Device Id: 5 0014ee 0ac59b7a4 Firmware Version: 05.01D05 User Capacity: 500.107.862.016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Fri Jan 6 18:56:37 2012 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF ENABLE/DISABLE COMMANDS SECTION === SMART Enabled. === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6960) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 84) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 961 3 Spin_Up_Time 0x0027 141 140 021 Pre-fail Always - 3950 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 875 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 10786 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 845 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 54 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 820 194 Temperature_Celsius 0x0022 102 093 000 Old_age Always - 41 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 199 000 Old_age Offline - 3 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. ~~~ Tags: Linux-Hardware